1. What method does a router use to build a Frame Relay map?

    2. A. ARP requests
    B. RARP requests
    C. Inverse RARP requests
    D. Inverse ARP requests

  2. What type of entries are found in Frame Relay switching tables?

    3. A. MAC address to DLCIs translations
    B. Only incoming ports and DLCIs
    C. Only outgoing DLCIs
    D. Incoming/outgoing ports and DLCIs

  3. What command is used to configure a subinterface that will forward broadcasts and routing updates?

    4. A. router(config-if)#interface serial 1 multipoint
    B. router(config-if)#interface serial 1 point-to-point
    C. router(config-if)#interface serial 1.1 multipoint
    D. router(config-if)#interface serial 1.1 point-to-point

  4. Which of the following is a common LMI extension?

    5. A. Multicasting
    B. Global addressing
    C. Simple flow control
    D. Virtual circuit status messages

  5. Which of the following is true about basic (non-extended) Frame Relay?

    6. A. Static maps can not be created
    B. Supports only PVCs with local significance
    C. Supports only PVCs with global significance
    D. Addresses are used to identify network interfaces

  6. On a point-to-point Frame Relay connection, what does each point-to-point connection require?

    7. A. A unique encapsulation type
    B. A separate subinterface
    C. An IPX address
    D. A direct physical connection

  7. What command is used to set Frame Relay encapsulation?

    8. A. router>encapsulation frame-relay
    B. router(config)#encapsulation frame-relay
    C. router(config-if)#frame-relay encapsulation
    D. router(config-if)#encapsulation frame-relay

  8. What does CIR designate in a Frame-Relay connection?

    9. A. Guaranteed rate that the service provider commits to providing
    B. Maximum data burst rate that the switch can handle
    C. Number of simultaneous virtual circuits available from a service provider
    D. Number of simultaneous DLCIs that can be established across the cloud

  9. Which of the following is a mandatory byte in the LMI frame?

    10. A. FCS
    B. Global addressing
    C. Information element
    D. Protocol discriminator

  10. When using Frame Relay, what command displays both the DLCI and LMI information on the serial 0 interface?

    11. A. show interface serial 0
    B. show interface frame-relay
    C. show frame-relay serial 0
    D. show frame-relay information

  11. What is the purpose of LMI?

    12. A. Informs the hub which PVCs are available
    B. Determines the operational status of PVCs
    C. Ensures the PVC shutdown during inactivity
    D. Eliminates the need for DLCIs

  12. What command displays whether a Frame Relay connection is sending and receiving data?

    13. A. show line
    B. show version
    C. show interface
    D. show receiving

  13. What is required to configure multiple DLCIs on a single router interface?

    14. A. A single network address
    B. Multiple LMIs
    C. Subinterfaces
    D. Multiple IP addresses on the same subnet

  14. What are Frame Relay flags used to indicate?

    15. A. Country of origin
    B. Error detection
    C. Beginning and ending of the frame
    D. Congestion control method

  15. What IP protocol does Frame Relay use for error correction?

    16. A. ICMP
    B. UDP
    C. TCP
    D. SPX

  16. What does Frame Relay use to prevent routing loops?

    17. A. Holddown timers
    B. Lower convergence times
    C. Increased router updates
    D. Split horizon

  17. How are DLCIs used by Frame Relay?

    18. A. Identify users
    B. Identify physical connections
    C. Identify logical connections
    D. Phone company tariffs

  18. Frame Relay operates at what two layers of the OSI model?

    19. A. Network and data link
    B. Data link and physical
    C. Transport and network
    D. Physical and network

  19. Which of the following optional Frame Relay encapsulation type is used if the remote router is a non-Cisco router?

    20. A. IETF
    B. Broadcast
    C. Protocol-address
    D. Payload-compress

  20. Using Cisco IOS release 11.2 or later, how is the LMI type set?

    21. A. Autosensing
    B. Requires a default setting
    C. Set to ANSI
    D. Set to Cisco

  21. What is the purpose of a Frame Relay map?

    22. A. Establish the entire route from beginning to end points
    B. Workstation address resolution
    C. Router next-hop address resolution
    D. Provides routing functionality to frame relay switches

  22. What router command will display the Frame Relay tables?

    23. A. show interface
    B. show frame-relay route
    C. show ip route
    D. show frame-relay map

  23. What significance do DLCIs have in a Frame Relay network?

    24. A. Global significance
    B. Local significance
    C. Both local and global significance
    D. DLCIs have been replaced by LMI processes

  24. What is an advantage of a public Frame Relay service?

    25. A. There is no charge for the service
    B. The network equipment is managed by the service provider
    C. Eliminates the need to purchase equipment
    D. Eliminates the need for DLCIs
  25. What command is used to verify a Frame Relay configuration?

    26. A. show version
    B. show startup config
    C. show running config
    D. show frame-relay pvc